Tektronix Thermometer P6131 Manual de usuario

Instruction ManualP613110X Passive Probefor 2400 Series Oscilloscopes070-5514-03*P070551403*070551403WarningThe servicing instructions are for use by

Specifications4P6131 Instruction Manual@25% Duty Factor=(1/2 Peak V) RMS@50% Duty Factor=(1.414 (Peak V)) RMSSpecial case of square wave:@20% Duty Fac

SpecificationsP6131 Instruction Manual5Frequency (MHz)500100101 10 100Voltage(RMS)Figure 4: Typical P6131 voltage derating versus frequencyTable 2: En

Specifications6P6131 Instruction ManualTable 4: Certifications and compliances EC Declaration ofConformityCompliance was demonstrated to the following

P6131 Instruction Manual7Service InformationWARNING. The following instructions are for use by qualified service personnelonly. To avoid electrical sh

Service Information8P6131 Instruction ManualTable 5: Performance verification and adjustment test equipment (cont.)Description Example productMinimum

Service InformationP6131 Instruction Manual94. Adjust the sine wave generator output amplitude to produce a 6-divisiondisplay on the test oscilloscope

Service Information10P6131 Instruction Manual6. Remove the coax cable from the test setup. Connect the P6131 probe outputto the same vertical input on

Service InformationP6131 Instruction Manual11To adjust the probe low-frequency compensation do the following:1. Connect the probe output to the test o

Service Information12P6131 Instruction ManualOver compensatedUnder compensatedCorrectFigure 7: Low-frequency compensation, optimizing the waveformTo a

Service InformationP6131 Instruction Manual138. Connect the probe output to the oscilloscope vertical input.9. Connect the probe tip through the probe

Copyright © Tektronix, Inc. All rights reserved.Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this pu

Service Information14P6131 Instruction ManualR2010R2020R2021C1010R2010C1010C2010R2021R2020Plastic-shell versionMetal-shell versionFigure 8: High-frequ

Service InformationP6131 Instruction Manual15MaintenanceUse the following procedures to clean and maintain the P6131 probe.To remove accumulated dirt

Service Information16P6131 Instruction Manual

P6131 Instruction Manual17Replaceable PartsThis section contains a list of the replaceable modules for the P6131 probe. Usethis list to identify and o

Replaceable Parts18P6131 Instruction ManualUsing the Replaceable Parts ListThis section contains a list of the replaceable mechanical and electrical c

Replaceable PartsP6131 Instruction Manual191234567891011121314151617Figure 10: P6131 probe with standard accessoriesReplaceable parts: P6131 probe and

Replaceable Parts20P6131 Instruction ManualReplaceable parts: P6131 probe and standard accessories (cont.)Fig. &indexnumberMfr. part numberMfr. co

Replaceable PartsP6131 Instruction Manual211 2 3 4 5 67 8 9 10 11 121314Figure 11: P6131 probe optional accessoriesReplaceable parts: P6131 probe opti

Replaceable Parts22P6131 Instruction ManualReplaceable parts: P6131 probe optional accessories (cont.)Fig. &indexnumberMfr. part numberMfr. codeNa

WARRANTYTektronix warrants that the products that it manufactures and sells will be free from defects in materials and workmanshipfor a period of one

Contacting TektronixProductsupportFor questions about using Tektronix measurement products, call toll free in North America:1-800-833–92006:00 a.m. –

P6131 Instruction Manual iGeneral Safety SummaryReview the following safety precautions to avoid injury and prevent damage tothis product or any produ

iiP6131 Instruction ManualService Safety SummaryOnly qualified personnel should perform service procedures. Read this ServiceSafety Summary and the G

P6131 Instruction Manual1Operating BasicsThe P6131 probe is a subminiature, 10X, passive probe designed specifically foruse with Tektronix 2400 Series

Operating Basics2P6131 Instruction ManualGrounding the ProbeConnect the probe to the instrument and connect the ground lead to groundbefore making any

P6131 Instruction Manual3SpecificationsThe characteristics listed in Table 1 apply to P6131 probes installed on Tektronix2445 and 2465 oscilloscopes o