Tektronix MTM400 Manual de usuario Pagina 168
- Pagina / 197
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Interface Configuration and Interpretation
3-124 MTM400 MPEG Transport Stream Monitor User Manual
BER (Pre-Viterbi)
This indicator reads the BER in the channel, before any error
correction is applied.
Input Card Screen - COFDM
Figure 3-45: Input card screen - COFDM (Example)
Five LED indicators are available on the Readings section of the screen:
Overall RF Lock:
All the lock indicators are showing “in lock”, and the signal is
being received normally.
TPS Lock Transmission Parameter Lock, showing true if the ruggedly
modulated TPS is being received.
AGC Lock Automatic Gain Control lock, showing the received signal is
within AGC control range.
SYR Lock Symbol Recovery Lock, showing that the FFT symbol recovery
system is in lock, allowing constellation data to be extracted.
FEC Lock Showing the Reed Solomon Forward Error Correction system is
in lock, and applying error correction to the received data.
- User Manual 1
- 071-1224-04 1
- Table of Contents 2
- List of Figures 5
- Table of Contents 6
- List of Tables 7
- General Safety Summary 8
- CAUTION 9
- Refer to Manual 9
- Protective Ground 9
- (Earth) Terminal 9
- Service Safety Summary 10
- Preface 11
- Related Material 12
- Manual Conventions 13
- Getting Started 14
- Accessories 16
- Installing the MTM400 22
- Powering Up the MTM400 27
- The Remote User Interface 28
- Details dialog: 29
- button in the browser.) 29
- Operating Basics 33
- Local Indicators 36
- Remote User Interface 37
- (See page 3-48.) 42
- Using WebMSM 46
- Using MLM1000 46
- User Interface Version 46
- Time Zones 47
- Reference 48
- Device View 49
- Device Status 50
- View Device Log 52
- Device Configuration 54
- Device Firmware Upload 59
- Device Information 63
- Stream View 65
- Detail Screen 70
- Tests Screen 71
- ○, Set - ●; 73
- Custom Screen 74
- Information Screen 76
- Programs Screen 78
- : The program number 79
- Change Bar 80
- Minimum Limit 80
- Maximum Limit 80
- PIDs Screen 82
- Adding a User PID 87
- Deleting a User PID 87
- PCR Drift Rate ** 88
- PID Groups Screen 89
- PCR Jitter Screen 96
- SFN Screen 104
- TMCC Screen 105
- SI Graphs Screen 106
- SI Tables Screen 110
- Tear off view 114
- Template 116
- Recording 119
- Log Screen 120
- Configuration Screen 124
- Service Log 128
- MTM400 Configuration Files 132
- Scheduling 137
- Scheduling Activities 139
- Local 142
- User Defined Offset 142
- -360 minutes 143
- Triggered Recording 144
- Triggered Recording Settings 145
- Pre-Trigger Recordings 147
- QPSK (L-Band) 153
- QAM (Annex A and Annex C) 158
- QAM (Annex B II) 162
- 8PSK (Phase Shift Keying) 173
- SMPTE310 Settings 176
- ASI Settings 176
- Appendices 177
- MAC Address 179
- IP Address 180
- Resetting the IP Address 180
- Tektronix Inc. Beaverton OR 183
- Network Set-Up 184
- Network Naming 185
- Network Latency 185
- Appendix B: Maintenance 186
- Rack Mounting 187
- Glossary 190
- PCR Inaccuracy graph, 3-49 195
Relacionado con productos y manuales para Monitores Tektronix MTM400
Monitores Tektronix 070-8811-08 Manual de usuario
(121 paginas)
(121 paginas)
Jenway Genova Plus French manuels
Manuels d'utilisation et guides de l'utilisateur pour Équipement Jenway Genova Plus French.
Nous fournissons des manuels en pdf 1 Jenway Genova Plus French à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentarios a estos manuales